Рассказываем и делимся интересным по прикладному искусству....Выставляем интересные работы....Собираем интересную информацию....... Просто общаемся...
За ранее приношу свои извинения,
если рядом с МК не окажется ссылки или данных автора.
Так как информация собираются в недрах интернета....
Переведи форум сам!
Последние темы
» Новенькое из моего....
Пт Сен 14, 2018 9:00 pm автор Admin

» Детсадиковская малышня..Мягкая игрушка
Вс Янв 17, 2016 12:35 am автор Admin

» Ссылки на кукольные сайты
Пн Мар 16, 2015 8:20 pm автор Goziraga

» Хорошая идея......
Сб Окт 04, 2014 8:38 pm автор Admin

» Лайфхакинг
Сб Окт 04, 2014 8:30 pm автор Admin

» Вышиваем носик.....
Сб Окт 04, 2014 8:16 pm автор Admin

» Как перенести фото......
Сб Окт 04, 2014 8:15 pm автор Admin

» Пинеточки....
Сб Окт 04, 2014 7:18 pm автор Admin

» Тапочки, тапочки......крючок
Сб Окт 04, 2014 7:16 pm автор Admin

» Носки, носки...... крючком
Сб Окт 04, 2014 7:12 pm автор Admin

Поделись с другом!
Март 2019

Поделиться | 

 Thread Holder pattern

Перейти вниз 

Стрелец Дата регистрации : 2011-02-13
Возраст : 46

СообщениеThread Holder pattern

I first showed a picture of my thread holder a number of people asked
if I had a pattern. I made mine one morning at my stitching morning, it
does not have a pattern so I thought I would show you how it is made.
Firstly cut 4 strips 7 1/2 inches X 2 1/2 inches then 4 from a contrasting fabric.
Lay them on your cutting board like this.
Lay the next 4 right sides together as above.
This step is important pick up the strips and put a pin in as above, then do the same to the bottom layer.
Sew together with a 1/4 inch seam.
You should have 4 pieces like this. Press seams open.
Lay 2 on your cutting mat as above.
one over so that you have right side together, and seams meeting. Sew
together with a 1/4 inch seam. Do the same with the other 2 pieces.
Press seams. You will now have 2 pieces that look like this.
Lay them right side together you should have contrasting fabrics on top of one another.
around the outside with a 1/4 inch seam leaving a small hole for
turning. Clip the top corners and clip into the the inside corners. Turn
inside out roll and press the seams. Slip stitch the opening closed.
Fold one arm on to the next one. As above.
I use ladder stitch to join these seams. Starting from the inside corner going to the open end.
As you can see you are joining then together along a seam.
Taking care to catch the side that are closest. Do this for all 4 arms.
Your seams if done correctly will have a wrong and a right side. Above is the right side which will be the outside.
is how the inside will look. If you look at the finished holder it has a
section that folds over I stitch up to about 3/4 inch from the top then
place the thread through and stitch the seam the other way. This is
hard to explain but if you stitch the same way all the way to the end of
the seam you will have an inside seam on the outside when you fold the
top over.
This is my thread holder as it sit on the arm of my lounge. I should empty it more often.
always use this pattern as it was intended do not reproduce it in any
way. It would be nice to see some finished thread holders. I know lots
of people visit and do not leave a comment so let me know how you go
with this.
They are great little inexpensive - quick to make gifts.

One wet cold afternoon when boredom had set in the family found another use for it.......


Я не волшебник !
Вернуться к началу Перейти вниз
Опубликовать эту запись на: diggdeliciousredditstumbleuponslashdotyahoogooglelive

Thread Holder pattern :: Комментарии

Нет комментариев.

Thread Holder pattern

Вернуться к началу 

Страница 1 из 1

Права доступа к этому форуму:Вы не можете отвечать на сообщения
Кладовая ! :: Пэчворк и текстильные штучки :: Мастер - классы-